NASSCOM Placement Papers
NASSCOM Reasoning Ability
NASSCOM Aptitude Paper
NASSCOM Verbal Ability
NASSCOM Technical Test - 2014
NASSCOM Technical Q & A - 14 September 2012
NASSCOM Verbal & Analytical Ability- 25 Nov 2012
NASSCOM Technical Paper - 25 November 2012
NASSCOM Written Test - 2012
L & T Infotech
Placement Papers for All Companies
Amiti Software Technologies
Ashok Leyland Ltd
AT & T
AXA Technology Services
Bharti Airtel Ltd
Blue Star Infotech
Citicorp Overseas Software Ltd
CtrlS Datacenters Ltd
Ernst & Young
Harita - TVS
HTC Global Services
IBS Software Services
IndiaBulls Power Limited
Jindal Steel and Power Limited
L & T
L & T Infotech
Linde India Ltd
Lucas - TVS
Mahindra Engineering Services Ltd
Poornam Info Vision
PSI Data Systems Limited
SAP labs India
Sutherland Global Services
UTC Aerospace System
NASSCOM Chemical Engineering Paper - 25 Nov 2012
Posted on :15-02-2016
NASSCOM Chemical Engineering Paper - 25 Nov 2012:-
Q1. In a fuel cell, chemical energy is converted into
(a) electrical energy directly.(b) mechanical energy.(c) electrical energy and stored therein.(d) none of these.
Q2. An example of unsteady non uniform flow is the flow of liquid under pressure through a
(a) tapering pipe at constant flow rate.(b) tapering pipe at either decreasing or increasing flow rate.(c) long pipeline of constant diameter.(d) none of these.
Q3. Milligram of KOH required to saponify 1 gm of oil is called its ..... number.
(a) saponification(b) acid(c) precipitation(d) emulsion
Q4. With increase in carbon percentage in steel, its
(a) yield(b) elongation percent increases.(c) tensile strength increases.(d) impact strength increases.
Q5. Which of the following is not a ferromagnetic material?
Q6. Which of the following is not an ore of iron?
(a) Chalcopyrite(b) Magnetite(c) Hemetite(d) Limonite
Q7. ....... property of a material is determined by the Herbert Pendulum device.
(a) Hardness(b) Tensile(c) Toughness(d) Compressive
Q8. The passage between the nozzle and the .......... is called sprue in case of injection moulding.
(a) runner(b) cylinder(c) mold(d) none of these
Q9. Galena is an ore of
(a) iron(b) copper(c) lead(d) aluminium
Q10. Electrode potential is not concerned with the measurement of
(a) pH value(b) temperature(c) viscosity(d) density
Q11. Pick out the wrong statement.
(a) In a thin spherical shell under internal pressure, hoop stress is equal to the half of axial stress.(b) Thermoplastic material does not follow Hookes law of elasticity.(c) Components under longitudinal compression is called struts and the load under which strut fails is called crippling or buckling load.(d) At low temperatures (sub-zero) in pressure vessels, the ductility of metal diminishes and brittle fracture occurs while at high temperature in pressure vessels, embitterment of material may take place.
Q12. Nitrogen compounds are not used in the manufacture of
(a) fertilizers(b) gun powder(c) tip of match sticks(d) explosive
Q13. The factor of safety for brittle materials (having elongation <5%) is based on the ----- stress.
(a) yield(b) proof(c) ultimate(d) none of these
Q14. Area under the stress-strain curve upto the .... is referred to as the modulus of resilience.
(a) yield strength(b) elastic limit(c) proportional limit(d) maximum point
Q15. Chalcopyrite is an ore of
(a) lead(b) aluminium(c) copper(d) zinc
Q16. The pH value is the measure of hydrogen ion concentration in a solution. The term pH stands for the ........ in the solution.
(a) power of hydrogen ion concentration(b) percentage of hydrogen ions(c) presence of hydrogen ions
(d) none of these
Q17. X-rays are
(a) positively charged.(b) negatively charged.(c) neutral.(d) of higher wavelength than visible light.
Q18. Aluminium is extracted from
(a) chalcocite(b) bauxite(c) galena(d) none of these
Q19. Common salt is produced from sea water in India generally by the ........... method.
(a) freeze drying(b) solar evaporation(c) electrolytic(d) none of these
Q20. A material lacking in toughness is usually termed as
(a) plastic(b) malleable(c) brittle ductile(d) ductile
Q21. The hydraulic radius of a circular pipe of diameter d flowing full is
(a) d/4(b) d/2(c) 2d/3(d) d/3
Q22. Oxygen content below .... percent in air contaminated with nitrogen does not support combustion and is unsafe for human exposure.
(a) 18(b) 16(c) 14(d) 12
Q23. Pig iron is
(a) made from cast iron.(b) made from wrought iron.(c) the one, which comes out of the blast furnace.(d) free from impurities.
Q24. Youngs modulus of a material is the measure of its
(a) stiffness(b) malleability(c) creep resistance(d) tensile strength
Q25. Otto cycle used in spark ignition petrol engines is also known as the constant....... cycle.
(a) volume(b) pressure(c) heat(d) none of these
Q26. ............. cycle is the most efficient thermodynamic cycle.
(a) Diesel(b) Otto(c) Rankine(d) Carnot
Q27. Plasma is
(a) a high temperature neutral gas.(b) nothing but ionised gas.(c) a source of steady and highest controllable pressure.(d) formed at very low temperature.
Q28. What is the pH of distilled water?
(a) 0(b) 1(c) 7(d) 14
Q29. Gantt charts are used for streamlining the
(a) inventory control(b) production schedule(c) sales forecasting(d) quality control
Q30. Cobalt - 60 is used as a source of ...... in medical therapy & industrial radiography.
(a) X-rays(b) g-rays(c) a-rays(d) β-rays
Q31. ............. wire is never used for making the heating element.
(a) Nichrome(b) Kanthal(c) Invar(d) None of these
Q32. Annealing of cast iron
(a) softens it to facilitate machining.(b) decreases the free carbon.(c) increase the strength.(d) none of these
Q33. A good abrasive
(a) should be friable.(b) should have low refractoriness.(c) is made up of large size of crystals.(d) should be soft.
Q34. L.D. (Linz-Donawitz) converter is used in the production of
(a) copper(b) steel(c) zinc(d) aluminium
Q35. ...... has the highest melting point out of the following.
(a) Tungsten(b) Zirconium(c) Molybdenum(d) Tantalum
Q36. Minimum diameter of the tube used for making water manometer should be ....... mm to avoid a correction for the effect of capillarity.
(a) 1(b) 2.5(c) 4(d) 6
Q37. Permanent set in a material is produced by subjecting it to
(a) triaxial loading.(b) fatigue loading.(c) stresses beyond the elastic limit.(d) tensile & compressive loads simultaneously
(a) can not be used in the form of pressure sensitive tapes.(b) can not join two dissimilar metals.(c) cure instantaneously after application on a surface.(d) none of these.
Q39. The tensile strength of plastics ranges from .......... kg/mm2.
(a) 10 to 50(b) 50 to 100(c) 0.01 to 0.1(d) 0.1 to 10
Q40. ..... test is the appropriate test to determine whether a material is ductile or brittle.
(a) Impact(b) Cupping(c) Hardness(d) Tensile
Q41. ........... number determines whether the fluid flow in an open channel is supercritical, critical or sub-critical.
(a) Mach(b) Reynolds(c) Froude(d) Weber
Q42. The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
(a) rigid(b) tough(c) ductile(d) plastic
Q43. Out of the following, the joint produced by ............ has the lowest strength.
(a) soldering(b) welding(c) brazing(d) rivetting
Q44. Thermoplastics are never moulded using
(a) injection moulding(b) blow moulding(c) extrusion(d) compression moulding
Q45. Which of the following is the terminology used for the temperature at which the phase changes occur in a metal?
(a) Critical temperature.(b) Recrystallisation temperature.(c) Phase transformation temperature.(d) Transition temperature.
Q46. While the bin cards are used in the effective stores management, the queing theory is associated with the ..... time.
(a) waiting(b) idle(c) inspection(d) tool replacement
Q47. Which of the following is not an explosive?
(a) TNT(b) CMC(c) RDX(d) Lead azide
Q48. The process of removal of scale formed during hot rolling of steel is termed as
(a) descaling(b) short blasting(c) pickling(d) skimming
Q49. Which of the following is a synthetic abrasive?
(a) Corundum(b) Emery(c) Pumice(d) Silicon carbide
Q50. Ester is formed, when an alcohol reacts with
(a) carboxylic acid(b) aldehyde(c) ketone(d) ether